RC MAKER

Adjustment To set the correct width, simply loosen the screw and slide to the correct width. Fully closed is 100mm, so depending on your post widt...

Two-piece RC Maker Slimflex top deck for the Xray X4 touring car. With this two-part top deck from "Down Under Australia" you get another setup op...

Two-piece RC Maker Slimflex top deck for the Xray X4 touring car. With this two-part top deck from "Down Under Australia" you get another setup op...

These brass weights from RC Maker are mounted on the chassis at the rear of the Xray X4. What makes the weights (6 g per side) so special is easy...

With this 12g brass plate from RC Maker you can mount your speed controller (ESC) floating above the chassis and at the same time add another 12g ...

Standard 13g brass floating plate for the RC Maker Electronics Floating Plate Set for the XRAY X4 This is the plate ONLY and it does not come wit...

This set from RC Maker is suitable for attaching the receiver, transponder and engine fan in your Xray X4 touring car. The clever design allows yo...

The RC Maker Centraflex top deck offers you a lot of options for tuning your X4 touring car from Xray. At first glance, this top deck may not diffe...

One-piece RC Maker Slimflex top deck for the Xray X4 touring car. With this one-piece top deck from "Down Under Australia" you get another setup ...

One-piece RC Maker Slimflex top deck for the Xray X4 touring car. With this one-piece top deck from "Down Under Australia" you get another setup ...

This 18 g brass strut is mounted on the chassis behind the engine mount of the Xray X4. With the 5 available holes for screwing you can additiona...

This set from RC Maker is suitable for attaching the receiver, transponder and engine fan in your Xray X4 touring car. The clever design allows y...

These brass weights from RC Maker are mounted in front of the servo and the battery of the Xray X4. What makes the weights (9 g per side) so spec...

Standard 19g brass floating plate for the RC Maker Electronics Floating Plate Set for the XRAY X4 This is the plate ONLY and it does not come wit...

With this carbon fiber plate from RC Maker you can mount your speed controller (ESC) floating above the chassis. Because the controller is floatin...

Ceramic ball bearing set for the Xray X4 touring car. The set includes 14 high-quality ceramic bearings from ABEC7, which are made of the highest ...

The steering deflection is an important setup parameter on every RC car. Especially in the on-road classes, a small change in the steering deflecti...

The RC Maker carbon fiber steering levers are available for the front and rear axles of the Xray X4 touring car. They are 3mm thick, making them s...

The RC Maker carbon fiber roll center shims are very practical and can be installed very quickly in your Xray X4 touring car. The annoying unscrewi...

With these 3D printed parts you can install the station of your Arrowmax tire heating blankets (AM-174010) directly in the RC Maker Car Stand (RCM...

The RC Maker carbon fiber roll center shims are very practical and can be installed very quickly in your Xray X4 touring car. The annoying unscrew...

The RC Maker brass roll center shims are very practical and can be installed very quickly in the Xray X4 touring car. The annoying unscrewing of t...

The RC Maker brass roll center shims are very practical and can be installed very quickly in the Xray X4 touring car. The annoying unscrewing of t...

The RC Maker brass roll center shims are very practical and can be installed very quickly in the Xray X4 touring car. The annoying unscrewing of th...

The RC Maker brass roll center shims are very practical and can be installed very quickly in the Xray X4 touring car. The annoying unscrewing of t...

RC Maker presents a new brass tuning part for the Awesomatix A800MMX touring car! This is a 10g weight that is attached directly next to the stee...

RC Maker presents this new floating GeoCarbon carbon fiber servo mounting plate for the Xray X4 touring car! This carbon fiber plate is a perfect...

RC Maker presents this set of 2 brass weights for your Xray X4 touring car! The two weights are mounted at the front of the Xray X4 touring car, ...

RC Maker presents a new brass tuning part for the Xray X4 touring car! This is a 13g weight that is attached directly next to the steering servo ...

With the 3D Pro Turnbuckle tool from RC Maker, assembling your Awesomatix turnbuckles and camber rods becomes much easier and more convenient. Sc...

RC Maker introduces its brand new over-engine wiring system for your mid-engine touring car! Wiring a mid-engine touring car is harder than ever, ...

RC Maker introduces its brand new over-engine wiring system for your mid-engine touring car! Wiring a mid-engine touring car is harder than ever, ...

RC Maker introduces its brand new over-engine wiring system for your mid-engine touring car! Wiring a mid-engine touring car is harder than ever, a...

Since the new design of the BD11 (and BD12) does not have a conventional shock tower at the front, the Tweak Stick uses extension plates that appl...

If you switched to the BD11 from another brand, or only had the stick from the BD10... you will need end plates that fit the BD11! Get this kit a...

RC Maker`s product description: Introducing our carbon fiber bridge for our new 3D Pro Carbon Parts Tray! This bridge snaps together and simply ...

RC Maker`s product description: Introducing our brand new 3D Pro Carbon parts shell! Thanks to the latest FDM printing technology, we are able t...

RC Maker`s product description: Introducing our brand new 3D Pro Carbon parts shell! Thanks to the latest FDM printing technology, we are able t...

RC Maker`s product description: Introducing our 3D Pro Carbon Ultra-Lite Wing Mount & Anti-Tuck Stiffener Set for 1/10 EP Onroad! How good a...

RC Maker`s Product Description: Our brand new Shock Piston Height Tool is a great new tool that will make building your Awesomatix D2.2 shocks a ...